How to use this product
Ensure a clean, uniform substrate before application. Mask surrounding areas with layered tape and plastic for precise, clean edges. If required, apply SEMCO Liquid Membrane for waterproofing or use a Brown Coat for leveling and crack repair.
Prime with colored X-BOND Liquid and, while still tacky, apply the Scratch Coat (Liquid + Stone). Spread tightly in one direction with a broom to create texture. Allow to dry completely, then scrape and clean. This forms the bonding foundation—do not modify or skip this step.
Prime and apply two thin Skim Coats (Liquid + Stone) using a trowel in one direction, maintaining a wet-on-tacky method. After drying, sand high points if needed. Finish with MicroBond for refined texture and color consistency. Remove tape before fully dry and allow 12–24 hours to cure prior to sealing.
Select the appropriate sealer—SEMCO Sealer Matte, Titan Shield Gloss, Satin Stone, or Natural Shield—and apply as directed for desired finish and protection. Work evenly, allow full drying between coats, and apply from bottom to top on vertical surfaces. Avoid water for 48 hours and cleaners for 5 days. Maintain surfaces using SEMCO Stone Soap to preserve durability and appearance.
Finish Options
This kit provides everything you need to create your preferred SEMCO finish — Natural or Smooth — using the same core components, with simple adjustments noted in the included instructions.
MATERIAL AND INSTALLATION COST
per square foot
COST OF OWNERSHIP
over 10 years
MICROCEMENT COMPARISON CHART
Thickness match-up: X-Bond Microcement (1/8") vs common 1/16" systems (LVT, Natural Stone/Ceramic Tile as thin-veneer or tight-joint installs, and Epoxy)
| Feature / Property |
X-BOND MICROCEMENT
|
RETAIL MICROCEMENT |
LVT |
NATURAL STONE / CERAMIC TILE |
EPOXY |
|---|---|---|---|---|---|
| Thickness | 1/8" (≈3 mm) | 1/8" (≈3 mm) | 1/16" (≈1.5 mm) | ~1/16" tight-joint veneer | 1/16" (≈1.5 mm) |
| Surface Strength (PSI) | >4000 PSI | 1500-2500 PSI | 200–300 PSI | 3000–3500 PSI | ≈2500 PSI |
| Bond to Substrate | Chemical + Mechanical | Mechanical Bond only | Adhesive only | Mortar/thin-set | Epoxy bond |
| Crack Resistance | High (Flexible) | Moderate | Low-Moderate | Low | Low-Moderate |
| Interior vs Exterior Use | Both — UV-Stable & Weather Resistant | Primarily Interior | Interior Only | Both (Exterior Graded Stone Only) | Interior Only |
| Weight Load on Structure | Lightweight | Moderate | Lightweight | Heavy vs. substrate | Moderate |
| Design / Texture Range | Unlimited (troweled) | Limited (Pre-Blend Formulas) | Factory patterns only | Fixed natural pattern | Gloss, limited texture |
| Repair & Renewal | Re-coat / Spot Repair | Replace plank | Requires Re-Sealing | Replace tile/section | Grind & re-pour |
| Install Speed | Fast (multi-coat) | Fast | Fast | Slow | Moderate |
| Substrate Versatility | Concrete, tile, drywall, plywood, plaster, DensShield… | Concrete / Cement Board Only | Flat subfloor only | Masonry/rigid only | Primarily concrete |
| Custom Color & Finish | Fully customizable | Limited | Limited | Limited | Limited |
Approximately ⅛ inch, depending on the desired texture and finish. Coverage Rate:
Around 108–130 ft² per kit, depending on surface condition and number of coats.
Suitable Surfaces:
Can be applied over concrete, tiles, plasterboard, MDF, cement sheet, existing screeds, and other stable, prepared substrates.
Adhesion:
Exceptional bond strength — designed to apply directly over most surfaces without the need for removal or demolition.
Curing Time:
Light foot traffic after 24 hours; fully cured within 5–7 days (depending on temperature and humidity).
Finish Options:
Available in matte, satin, and gloss sealers — allowing you to choose the perfect balance of appearance and protection.
Colour Range:
Customisable palette inspired by natural tones and modern architectural design.
Maintenance:
Simply clean with a neutral pH cleaner and reseal periodically for lasting performance and beauty.
Recommended Use:
Suitable for both professional applicators and confident DIY renovators looking for a high-end, seamless finish.
What surfaces can it go over? Can it go over the tile?
Can homeowners purchase the product and install it?
What are the advantages of microcement compared to tiles?
What is the total thickness of X-Bond Microcement?
On which surfaces can X-Bond Microcement be applied?
Is the X-Bond Microcement suitable for wet rooms or pools?
Readworthy Inspirations
View all-
The Difference Between Shower Tile Resurfacing,...
When it comes to remodeling your bathroom, one of the biggest decisions you’ll face is what to do with your existing shower tile. Should you resurface, refinish, or replace it entirely?...
The Difference Between Shower Tile Resurfacing,...
When it comes to remodeling your bathroom, one of the biggest decisions you’ll face is what to do with your existing shower tile. Should you resurface, refinish, or replace it entirely?...
-
Spalling Concrete: Causes, Prevention, and Long...
Is your concrete driveway, patio, or wall flaking and chipping like old paint?This unsightly issue is called spalling concrete, and it’s one of the most common forms of surface damage...
Spalling Concrete: Causes, Prevention, and Long...
Is your concrete driveway, patio, or wall flaking and chipping like old paint?This unsightly issue is called spalling concrete, and it’s one of the most common forms of surface damage...
-
How to Update Floor Tile Without Removing It: T...
Are your old, chipped, or outdated floor tiles ruining the look of your space? You're not alone. Many homeowners and property managers face this dilemma—torn between the hassle of removing...
How to Update Floor Tile Without Removing It: T...
Are your old, chipped, or outdated floor tiles ruining the look of your space? You're not alone. Many homeowners and property managers face this dilemma—torn between the hassle of removing...
- Choosing a selection results in a full page refresh.
- Opens in a new window.